3ft NEMA 5-15P to C19 PDU Power Cord, 14 AWG SJT Heavy Duty, 15A/125V, UL Listed, Black

3ft NEMA 5-15P to C19 PDU Power Cord, 14 AWG SJT Heavy Duty, 15A/125V, UL Listed, Black

This NEMA 5-15P to IEC 60320 C19 heavy-duty power cord connects C20-inlet equipment to a standard North American 120V wall outlet. Built with 14 AWG conductors rated for 15A at 125V, it delivers dependable power to rack PDUs, UPS units, and high-draw servers without an adapter, making it a practical replacement or upgrade cord for data center and server-room deployments.

The NEMA 5-15P plug is the standard US three-prong grounded connector found on virtually every 120V wall outlet, dedicated outlet, and rack power strip. Its fully molded body and grounded blade configuration give a secure, low-resistance connection to existing electrical infrastructure in offices, IT closets, and data center environments.

The IEC 60320 C19 receptacle is the higher-current member of the IEC connector family and seats onto the C20 inlets built into large PDUs, UPS systems, and power-hungry servers. Pairing a C19 receptacle with a NEMA 5-15P plug lets equipment that expects a C20 inlet run from an ordinary 120V/15A circuit, with this cord capping current at the 15A the plug and conductors safely support.

Safety certifications include UL and cUL listing, confirming the cord meets North American electrical standards for construction and flame resistance. RoHS and REACH compliance show the cord is free of restricted hazardous substances, supporting procurement requirements for professional and regulated installations.

The 105°C-rated SJT jacket and fully molded strain-relief connectors are built for the thermal load and constant flexing inside equipment cabinets. The heavier 14 AWG copper reduces voltage drop versus thinner cords, which matters when feeding sustained loads in tightly packed racks where ampacity and equipment compatibility drive cable selection.

Compatibility & Ordering Information: This cord fits any device with an IEC 60320 C20 inlet, including rack PDUs, UPS units, blade and tower servers, and network appliances drawing up to 15A at 125V. For lower-draw devices that use a C13 inlet, the NEMA 5-15P to C13 cord is the correct match, and for in-rack jumpers a C20 to C19 cord extends an existing PDU feed. The cord is available in multiple lengths to suit in-rack runs and outlet-to-equipment distances.

FAQ

What is the difference between a NEMA 5-15P to C19 and a NEMA 5-15P to C13 power cord?

The difference is the equipment-end connector and current rating. A C19 receptacle is the higher-current connector that seats on C20 inlets found on large PDUs, UPS units, and high-draw servers, while a C13 connects to the more common C14 inlets on standard computers and monitors. This C19 cord uses 14 AWG for 15A loads; C13 cords are typically 18 AWG for 10A.

Is this power cord compatible with my PDU, UPS, or server?

Yes, if the device has an IEC 60320 C20 inlet, the C19 end mates with it directly. The NEMA 5-15P plug then connects to any standard US 120V/15A outlet. Confirm the device draws no more than 15A at 125V, which covers most rack PDUs, UPS units, and servers fed from a standard wall circuit.

What wire gauge do I need for a 15A power cord?

14 AWG is the correct gauge for a 15A/125V cord. Its larger copper cross-section carries the full 15A continuously with lower voltage drop and heat than a thinner 16 or 18 AWG cord, which is why heavy-duty server and PDU cords use 14 AWG rather than the 18 AWG found on light-duty computer cords.

How do I connect this cord to a PDU or server?

Plug the IEC 60320 C19 end into the device's C20 inlet until it seats fully, then plug the NEMA 5-15P end into a standard grounded 120V outlet or rack power strip. No tools or adapters are required. The fully molded connectors and 105°C SJT jacket are built for repeated insertion and the heat inside server racks.

Which power cord is best for connecting a PDU to a standard wall outlet?

A NEMA 5-15P to C19 14 AWG heavy-duty cord is the best match when a PDU or UPS has a C20 inlet and your source is a standard 120V/15A outlet. The 14 AWG conductors and 105°C SJT jacket handle sustained 15A loads, and the molded NEMA 5-15P plug fits any standard North American receptacle.