15ft NEMA 5-15P to C13 Computer Power Cord, 14 AWG SJT, 15A/125V, UL Listed, Gray

The Cable Leader PW140-C2XX is a NEMA 5-15P to IEC 60320 C13 computer power cord built on a heavy-duty 14 AWG SJT conductor. One end terminates in a standard US three-prong wall plug; the other ends in a C13 receptacle that mates with the C14 inlet found on desktop PCs, monitors, printers, network switches, and servers. Where most computer power cords use thin 18 AWG wire rated for 10 amps, this cord steps up to 14 AWG and a 15A/125V rating, giving high-wattage equipment meaningful current headroom on a dedicated branch circuit.

The wall end is a NEMA 5-15P plug, the connector on virtually every 120V power cord in North America. Its two flat blades and round ground pin fit any standard 5-15R household or office outlet, as well as the 5-15R outlets on most rack PDUs and UPS units. The plug is molded directly to the cord with integrated strain relief, so the blade terminals and jacket are locked into a single body that resists pull-out during routing and repeated reconnection.

The device end is an IEC 60320 C13 receptacle, the female connector that slides onto the C14 power inlet built into computer power supplies and most IT hardware. The keyed, polarized housing ensures correct line, neutral, and ground orientation every time. Because the C13/C14 interface is an international standard, this single cord replaces the original equipment cord on hardware from virtually any manufacturer, making it a practical replacement and spare for mixed equipment fleets.

Electrical capability is set by the conductor and jacket. The 14 AWG (2.08 mm²) stranded copper conductors carry 15 amps continuous at 125 volts, and the SJT jacket is rated 300V, VW-1 flame retardant, and 105°C — a higher temperature ceiling than the 60-75°C SVT jackets typical of commodity cords. Certification covers both the cordage and the molded ends: UL file E204978 for the cable, UL file E210037 for the connectors, cUL for Canada, CSA file 204790, and RoHS compliance for restricted substances.

This heavier build matters most where current draw and heat are real concerns. High-wattage gaming and workstation power supplies, multi-drive servers, and equipment fed from a PDU in a warm cabinet all benefit from the extra conductor mass and the 105°C jacket. The 9.3 mm outer diameter stays flexible enough for tidy cable management behind a desk or inside a rack, while the gray (Pantone Cool Gray 9C) jacket helps distinguish heavy-duty runs from standard black cords during equipment audits.

Compatibility & Ordering Information — PW140-C2XX fits any device with a standards-compliant IEC 60320 C14 inlet, including desktop computers, monitors, printers, PoE network switches, and rack servers, and plugs into any standard NEMA 5-15R outlet or PDU/UPS convenience outlet. It is available in 3 ft, 6 ft, 10 ft, 15 ft, and 25 ft lengths; choose a shorter run for in-rack and behind-desk drops, and a longer run for outlet-to-rack or cross-room placement. Custom lengths, bulk packaging, and OEM kitting are available on request — contact Cable Leader for quotations.

Product Comparison: 14 AWG Heavy Duty vs 18 AWG Standard Computer Power Cord

FAQ

What is the difference between an IEC C13 and a C14 connector — and is this the same as a PS5 or laptop figure-8 cord?

The C13 is the female connector on the cord that plugs onto a C14 male inlet on your equipment, so this cord's C13 end powers any PC, monitor, or printer with a C14 inlet. It is not the same as a figure-8 (C7/C8) cord used by many game consoles and small electronics; those are 2-pin and will not fit a C13/C14 device.

Is this cord compatible with my desktop PC, monitor, and printer?

Yes, if the device has a standard IEC 60320 C14 power inlet — which covers the large majority of desktop computer power supplies, monitors, laser printers, network switches, and servers. The NEMA 5-15P plug fits any standard US 120V wall outlet or a NEMA 5-15R outlet on a rack PDU or UPS.

Do I need 14 AWG, or is 18 AWG enough?

Choose 14 AWG when the equipment draws high current or runs hot. A standard 18 AWG computer cord is rated 10A (about 1,250W); this 14 AWG cord is rated 15A/125V (about 1,875W) with a 105°C jacket, giving extra headroom for high-wattage PSUs, multi-drive servers, and PDU drops in warm cabinets.

Which end plugs into the wall?

The NEMA 5-15P end — the three-prong plug with two flat blades and a round ground pin — goes into the wall outlet, PDU, or UPS. The C13 receptacle end pushes onto the C14 inlet on your equipment. Both ends are keyed and polarized, so each only fits its correct mate.

Which power cord is best for a high-wattage PC or server?

For high-draw computers, workstations, and rack servers, a 14 AWG SJT cord like this one is the better choice over a standard 18 AWG cord because of its 15A/125V rating and 105°C jacket. Match the length to your layout — shorter for in-rack and behind-desk drops, longer for outlet-to-rack or cross-room runs.