10ft Slim Cat6a 10G Ethernet Patch Cable, 28AWG Bare Copper UTP, Snagless RJ45, Blue

The Slim Cat6a 28AWG UTP patch cable delivers 10 Gigabit Ethernet in a cable about 60% thinner than a standard 24 AWG Cat6a cord. At roughly 4.0 mm in diameter, it is built for high-density patch panels and racks where airflow and channel space are tight, and for desks and 10G home setups where a thinner cord routes cleanly behind equipment.

Both ends terminate in an 8P8C RJ45 modular plug wired to the T568B standard, with 50-micron gold-plated contacts that resist corrosion and keep contact resistance low. The plug seats in any standard RJ45 port on switches, routers, servers, patch panels, and NAS units, so the cable drops straight into existing network infrastructure.

The slim profile is the defining feature. A thinner jacket over four twisted pairs of 28 AWG bare copper reduces bulk in dense bundles, improves airflow across stacked rack gear, and frees channel space in 24-port and 48-port patch panels. Because 28 AWG has higher resistance than 24 AWG, these cables are intended for short-to-medium patch runs rather than full 100-meter horizontal links.

The cable carries strong third-party validation: marked UL E305668, cUL, and ETL verified to TIA/EIA-568-C.2, with RoHS compliance. The bare copper conductors meet the requirements for Power over Ethernet, so the same cable carries PoE to access points and cameras on short connections without a separate power run.

A translucent snagless molded boot protects the locking tab so the slim connector slides through crowded patch fields and cable bundles during moves, adds, and changes. Nine jacket colors support structured color-coding for port mapping, while the low-profile design keeps dense racks and 10G workstation areas tidy and serviceable.

The blue jacket is the common convention for general data and uplink runs, making standard network connections easy to identify at a glance in busy patch fields.

Compatibility & Ordering Information: This slim Cat6a patch cable works with any RJ45 equipment, including 10G network switches, routers, NAS units, servers, PoE devices, and gaming PCs, and is backward compatible with Cat6 and Cat5e gear. It is available in lengths from 0.5 ft to 75 ft and in nine colors. For full 100-meter horizontal runs, use a standard 24 AWG Cat6a cable; for in-wall backbone, use Cat6a solid bulk cable.

Product Comparison: Slim 28AWG vs Standard 24AWG Cat6a Patch Cable

Buyers choosing a Cat6a patch cable often weigh the slim 28AWG version against a standard 24AWG cord, since both are Cat6a rated and use RJ45 connectors. The table below summarizes the decision:

Choose slim 28AWG Cat6a for high-density panels, better airflow, and tidy 10G patch runs at the rack.
Choose standard 24AWG Cat6a for full 100-meter 10G channels, long horizontal runs, and high-power PoE.

FAQ

What is the difference between slim 28AWG and standard 24AWG Cat6a?

Slim 28AWG Cat6a is about 60% thinner, which improves airflow and frees channel space in high-density patch panels. Standard 24AWG Cat6a has lower resistance and supports full 100-meter 10G runs. Both are Cat6a rated to 500 MHz and use RJ45 connectors.

Does this slim Cat6a support PoE, PoE+, and PoE++?

Yes. The bare copper conductors carry Power over Ethernet and the RJ45 plugs fit any standard port. As a 28 AWG slim cable it runs warmer on long high-power PoE runs, so it is best for short PoE connections; for long high-power runs choose a standard 24 AWG cable. Bare copper matters, since copper-clad aluminum overheats under PoE.

How far can a 28AWG Cat6a cable run 10G?

Slim 28AWG Cat6a is best for short-to-medium patch runs, typically up to about 50 feet for reliable 10G. Its thinner conductors have higher resistance than 24AWG, so for full 100-meter 10G channels a standard 24AWG Cat6a cable is the better choice.

What is a patch panel cable, and why is slim 28AWG good for it?

A patch panel cable is a short patch cord that connects a patch panel port to a switch or another panel. Slim 28AWG is ideal here because its thin profile frees channel space and improves airflow in dense 24-port and 48-port panels where standard cables crowd the rack.

Which Cat6a cable is best for a high-density 24-port or 48-port panel?

For dense patch panels and stacked rack gear, slim 28AWG Cat6a is best because it saves channel space and improves airflow while keeping 10G performance on short runs. For long horizontal links or in-wall cabling, choose standard 24AWG Cat6a or solid bulk cable.